Is your urinal flush valve making noise? Wondering how to fix it? A Sloan flush valve urinal has a simple mechanism. You can solve it easily after figuring out the problem.
Your urinal flush valve may make noise if there is any leakage inside it or any stuck problem or has already worn out. In this post, we will help you learn what causes this problem and how to eliminate it.
Let’s dive in!
Why The Urinal Flush Valve Is Creating Noise
Your urinal flush valve can create noise for several reasons, which are listed below:
- Dirty Rubber Diaphragm
If you notice the valve doesn’t stop running even after completing the flushing, the rubber diaphragm might have become dirty or too old.
That is why the rubber diaphragm is getting hard and causing loud noises.
Getting rid of debris inside the rubber diaphragm is necessary to handle this mess.
- Overflow of Urinal Flush Valve
Is your urinal not flushing all the way? When there are clogged drain lines due to small debris accumulated inside the p-trap, it can cause an overflowing urinal flush valve.
This will ultimately cause excessive noise.
Alternatively, if the urinal drains have sediment deposits build-up, it can also cause overflow urinal flush valve. Figuring out the issue and implementing a solution based on it is crucial.
- Leaking Urinal Flush Valve
The fixture’s flushometer is the main culprit behind a leaky urinal flush valve. A flushometer plays a key role in performing the flush cycle smoothly.
But when there are leakage issues inside the urinal flush valve, you have to replace it. Changing the diaphragm might also be necessary.
This problem occurs when the water pressure or volume constantly fluctuates. This issue may pop up when using the urinal flush valve for a long time.
Watch this video with sound on to see you have the same problem.
How To Fix The Urinal Flush Valve That Is Creating Noise?
The solution of noise in a urinal flush valve will vary based on the problem. First, you have to figure out the type of problem your urinal flush valve is facing and utilize a solution accordingly.
- Fixing Stuck Urinal Flush Valve
If your overflow or stuck urinal flush valve is causing excessive noise, quickly addressing the problem is necessary. Otherwise, it will lead to additional problems. Here are the steps to follow.
At first, take out the splash guard. Remove urinal cakes too. Now locate the drain lid and remove it by unscrewing its nuts.
Get a plunger. Put it inside the drain. Keep pumping it. Then wait for a while. Again continue doing it. You should do it ill the water starts draining.
If the clogging is still there, you can use an auger. Put the auger inside the drain you did in the past. Keep pushing for several times. Do it until the clog removes.
After removing the clogging, use a urinal de-scaler to make the drain line smoother. Don’t forget to stick with the manufacturer’s guidelines to use the right method and quantity.
Let it stay for 10-15 minutes. Then, flush it properly.
- Fixing The Leaky Urinal Flush Valve
If your urinal flush has a leaking issue, quickly replacing the Sloan valve is necessary.
At first, locate the shut-off valve, which is situated at the lower part of the urinal. Take off the chrome from it.
Now, take a flat-head screwdriver and use it to rotate the valve screw in the opposite clockwise direction to turn off the water supply of the urinal.
Next, get channel lock pliers to unfasten the screw of the flushometer head. Also, take off the flush head lid.
This will give you better access to the internal part of the diaphragm. Be careful as water is more likely to spread once you take off the flush head lid.
Now, you can see the diaphragm. Take it out. Get the new diaphragm and install it. After properly installing the diaphragm, put back the flush head in its original place and fasten it properly.
Use a dry fabric to clean the wet area. Now, flush the urinal to ensure that you still hear any noise from it.
- Adjusting The Water Flow
The right side of the urinal flush valve includes a water control stop screw. Use a screwdriver to rotate it in a clockwise direction.
This will decrease the excessive water flow every time you flush it. Normally, excessive water flow causes water overflow or splash.
On the other hand, if the water flow is too low, the flushing system may not be powerful enough to remove waste. In such a situation, use the screwdriver to rotate it anti-clockwise direction.
How To Take Care Of Water Damage From A Urinal?
Though you are most likely to face leaking or overflowing issues after a certain time, some cautious actions can delay the process.
- Regularly use a powerful disinfectant to clean all the spotted areas.
- Install several fans in the restroom to keep the room free from unwanted moisture.
- Regularly check the development of mold any signs of cracking on tiles and walls.
- Avoid handling huge water damage since it requires extensive plumping skills. Let a professional handle it.
- While cleaning the bathroom regularly, inspect the drainage condition and if there are any leakage or slow draining issues.
- Whenever any problem arises, address it quickly without delaying any further.
- Keep some backup replacement parts at your home which require regular replacement.
- Invite a professional plumber on a monthly basis to inspect your plumbing components.
Conclusion
Are you still wondering about the urinal flush valve making noise? A urinal flush valve may make noise for various reasons, which we have already mentioned.
You first figure out the main reason behind this problem and solve the problem by following our above-listed solutions.
Hopefully, you have succeeded in solving the automatic urinal is not flushing and other issues. Ensure your urinal flush system regularly to ensure a proper function.
If you are still facing the problem, let us know in the comment section; we will try to solve it.
