The catch with contemporary bathroom editions is that they have an inevitable beauty drag that pulls you closer to buying them every time.
But, that doesn’t change the fact that bathroom essentials that are easy on the eyes won’t cause a few issues now and then.
This is why it’s essential to know about the American Standard Edgemere toilet problems. So, if you own these extensively, posh toilets, come and check out some crucial issues that you may be facing too.
American Standard Edgemere Toilet Issues
The trick here is to get acquainted with all the American Standard toilet problems. Once you get a complete understanding of the issues, you will also be able to comprehend the next steps leading to the maintenance and recovery of your beloved toilet.
So, let’s take a gander at some of the most common Edgemere toilet problems.
- Weak or Incomplete Flush
One of the most frustrating American Standard Edgemere toilet problems is a weak, inconsistent flush. You may find the bowl fails to fully clear waste or paper after flushing. There are several possible causes for a weak flush:
Clogged passages: Over time, mineral deposits can build up in the rim holes or other internal passages. Check the openings under the rim and use a bent wire to clear any blockages to restore flushing power.
Flapper failure: The rubber flapper seal at the base of the tank can warp or wear out over time, preventing a full flush. Replacing a leaky or faulty flapper will generally resolve fluid dynamics issues.
Low water level: If the water level is too low (say less than 1” below the rim), there may be insufficient siphon action during flushing. Check and adjust the tank fill height accordingly.
Lint or debris: Small items like unnoticed bath tissue, hair, or toys can clog passages or block sink holes and reduce efficiency. A thorough inspection and cleaning could significantly improve performance.
- Continuous Running
If your American Standard dual flush toilet runs continuously, the most likely culprit is a failing or misadjusted tank component. Troubleshooting steps include:
Adjust or tighten the flapper chain connection: A loose chain can lead to incomplete flapper closure, leading to running water as the tank slowly refills through the flush valve.
Clean the flapper seal: Hard water scale, rust, or other debris on the flapper seal can prevent a water tight connection to the flush valve, triggering continuous running.
Replace the flapper: As mentioned previously, over time the rubber flapper seal can warp or develop mineral deposits that inhibit flowing water. Replacing the flapper is generally an easy fix to stop running water.
Adjust fill valve height: If the water level is too high, the tank can slowly run as water trickles into the overflow pipe. Check and adjust height accordingly.
- Tank Does Not Refill
In some cases, the American Standard Edgemere toilet tank may fail to refill completely after flushing. Problems that can prevent full refilling include:
Faulty float: The fill valve shut off is operated by a float connected to a metal or plastic arm. If sediment or hard water scale sticks the float in position, this can prevent the fill valve from opening sufficiently to refill the tank.
Kinked supply line: Check for any bends or traps in the flexible supply line that may be restricting flow into the tank. Straighten or replace the supply line as needed.
Clogged fill valve: Mineral deposits, rust flakes or other debris trapped in the fill valve can partially block the inflow of water. Turn off, disconnect and thoroughly clean the fill valve components to restore full flow.
- Tube Or Valve Replacements
Water level and flush issues could occur within the roller camps, overflow pipes, and refill tubes in American Standard Edgemere toilets.
Moreover, water leaks can also erupt due to malfunctioning valves or if the valves are too old and worn out.
Thus, replacing the parts is the only solution for such integral component issues.
This can be a bit of a downer for many due to the extra costs.
Furthermore, water leaks or running continuously can also lead to irreparable issues if left alone for too long.
- Low Water Levels
Whether the flush of your toilet is half or full, if it stops working after pressing the flush button, you need to understand that it’s because of water level issues in the tank.
Sometimes when you press the flush lever, the lever releases automatically upon pressing.
Another reason why such inconsistencies occur is when the water level isn’t set high enough. This issue solely arises when the maximum setting or adjustment dial is inadequately set.
- No Dual Flushing System
Unfortunately, the American Standard Edgemere toilets do not have a dual flushing system. This is a significant downfall in the design given the era where a dual flushing system for any generic toilet is a given. Since the dual flushing system is absent, the toilet will evidently utilize more water.
Thus, even though the system comes with proper water conservation features, it will utilize more water than necessary.
So, it all boils down to the trade of balance at the end of it since, in the long run, it might not have severe consequences but more of a moral one.
- Not Compact
Let’s get it real, even though the Edgemere toilet has a very sleek design and ways of water conservation, it doesn’t come with the most compact design out there.
Compact toilets are a massive hit for users as they can fit in any bathroom size.
Therefore, if your bathroom is particularly small, you might have difficulty fitting the toilet in the desired spot if the measurements don’t cooperate.
- Small Toilet Bowl
Even though the American Standard Edgemere toilet has a standardized bowl, some users believe that it isn’t up to the mark. These toilets have extensive clean designs and structures.
However, the diameter of the bowl is relatively small for many. Moreover, when the bowl shape and size aren’t up to the mark, it might adversely affect many disabled users.
- Difficult Installation
With toilets that deem to have the classiest design, state-of-the-art construction, and intricate craftsmanship, it’s evident that users would think that the installation is a piece of cake too.
However, that’s not the case as, unfortunately, installing these American Standard Edgemere toilets is quite complex.
First off, the toilet itself is extremely heavy. Thus, installing the product on your own is out of the picture.
Second, the anchoring space allocation is too small compared to the required measurements.
Interestingly, even professional plumbers believe that these are tough to hook to the walls and floors.
You will also have to purchase a no-wax or wax ring for the installation. Overall, the entire procedure isn’t DIY-friendly.
The plastic seat is a nightmare to install. It needs the users to purchase too many extra tools for the installation and takes a toll on the professional or DIY-er during the whole process.
- The Seat Could Have Had A Better Build
The seats on the American Standard Edgemere toilets are seamless with a slow close feature and slim craftsmanship. However, there is room for significant improvement when it comes to the seats. The seats are made from fragile, thin plastic.
So, settling kids atop of it or leaning back is a big no. It will either bend inward or outward, given the situation. The utilization of thin plastics as such really takes a tremendous value out of the purchase.
- Issues With Alignment
Here’s another bummer with this toilet, the alignment on it is a bit off. Not only will the users and installers have back strain from the struggle, but they will face immense pressure while aligning the toilet.
The bolting ports are entirely concealed. Therefore, it is even harder to locate and understand how to align it in the bathroom accurately.
- Dirt Accumulation In Concealed Spaces
This toilet comes with many mysterious parts that have been intuitively enclosed within the system. To be fair, the concealed parts give the toilet a highly polished, clean, and neat exterior.
However, this hampers the installation process, and these covered spaces gradually accumulate dirt and grime. Since the toilet deals with water, it’s evident that there will be mineral build-ups.
Along with that, other dirt, grime, and residues seep into the toilet seat’s mounting holes with time and get severely soiled.
Not being able to clean the said area happens to be a big miss as well as the dirt accumulation would never truly stop.
Troubleshooting Tips For Poor Flushing
If your American Standard dual flush toilet fails to fully clear the bowl in one flush, try these troubleshooting tips before calling a plumber:
Double flush – Activate a second full flush cycle if waste persists
Check for clogs – Use an auger to root out any obstructions in rim holes or drainage passages
Monitor water level – Ensure correct factory fill line height of 1” below overflow tube
Clean faulty parts – Remove debris, scale on flapper, valves, rim holes
Replace flapper – A warped or leaky flapper allows water to leak out, reducing siphon effectiveness during flush
Increase water pressure – Low pressure under 80 PSI can impede flushing mechanics
Be patient and methodically test each solution. In many cases, a minor adjustment or DIY part swap restores proper toilet performance.
FAQs about American Standard Edgemere Toilet Problems
American Standard has faced multiple recent class action lawsuits over Edgemere and other toilet models regarding misleading water savings claims, product defects resulting in poor performance, high repair rates, and failure to meet advertised features. Recent settlements provided refunds or replacement parts.
Edgemere dual flush toilets come with a limited lifetime warranty that covers porcelain parts against leaks and breaks stemming from manufacturing defects. A 5 year warranty applies to mechanical parts like dual flush components. Normal wear and tear damages are excluded.
If your American Standard dual flush toilet fails to fully clear waste in one flush, it is likely caused by an obstruction, leaky flapper, incorrectly set water level, low water pressure, or clogged rim holes/valves. Methodically testing fixes like cleaning, adjustments, or part replacement typically resolves the issue.
If your toilet fails to flush whatsoever, first check the supply valve is open fully. Then troubleshoot the tank components like the flapper seal, chain, float, and fill valve for any debris, damage, or adjustments needed so the tank can refill and flush properly again. Test adding water manually if needed to isolate causes.
Conclusion
Don’t get us wrong; we think that the American Standard Edgemere toilet is an excellent investment. However, whether you should make the splurge or not is entirely in your hands.
If you ask us, we would say that you should consider it as an option despite the American Standard Edgemere toilet problems.
You see, sometimes the sleek design, easy cleaning and maintenance, and longevity of the product outweigh the cons. And that’s exactly what happens when you own this piece.